Appliance error codes, decoded. The right part, the first time.

Whirlpool Washer Error Code F21 — Long Drain

What F21 means Your Whirlpool front-load washer tried to drain and could not empty the tub within its drain window — about 8 minutes. Most of the time nothing is broken: the drain pump filter is clogged with lint, coins, and debris. Clean the filter and check the drain hose before you buy any part. (On older Duet models, the same fault can appear as F02.)
Safety: unplug the washer before opening the filter or any panel. Expect water — up to a few gallons if the tub is full — when you open the pump filter. Have a shallow pan and towels ready.

What the code means

F21 is Whirlpool's long-drain fault. The control board runs the drain pump and watches the water level sensor; if the level has not dropped after roughly 8 minutes of pumping, the cycle stops and F21 is displayed. The machine is draining — just too slowly — which is why this code is about restriction first and parts second. F21 appears on Whirlpool Duet, Duet Sport, and later WFW-series front-load washers, and on the Kenmore front-loaders built by Whirlpool on the same platform.

Likely causes, in the order to check them

Step-by-step fix

  1. Unplug the washer. Note how much water is left in the tub — a full tub tells you the drain barely worked at all.
  2. Check the drain hose first (2 minutes, no tools). Pull the washer out enough to see the hose: no kinks, no crush points. At the standpipe or laundry tub, the hose end should sit only a few inches into the drain — not shoved deep and not sealed airtight. The top of the drain loop should be within the height range in your model's installation guide.
  3. Clean the drain pump filter. On most Whirlpool front-loaders it is behind a small access door at the bottom front. Put a shallow pan and towels down, open the door, and use the small drain hose (if fitted) to empty the filter housing first. Then unscrew the filter counterclockwise, slowly — water will come out. Clear lint, coins, and debris, rinse the filter, and check the housing behind it for anything jammed against the pump impeller. Reinstall the filter snugly.
  4. If suds are suspect, run a rinse. If the failed load used a lot of detergent or non-HE detergent, run an empty rinse-and-spin (or drain-and-spin) cycle with no detergent. If F21 clears and stays cleared, suds were the problem — switch to HE detergent at the recommended dose.
  5. Test with a drain & spin cycle. Listen at the bottom of the machine: you should hear the pump hum steadily and water flow out. A steady hum with slow flow means a restriction remains. A loud buzzing or grinding suggests something in the pump. Silence means the pump is not running at all.
  6. Test the pump before replacing it (optional, multimeter). With the washer unplugged and the pump accessible, disconnect its two wire terminals and measure resistance across them. These pumps typically read in the 10–30 Ω range; an open (OL) or near-zero reading means the motor winding has failed. Confirm the exact specification in your model's tech sheet.

The part involved

If the path is clear and the pump has failed, the replacement on most Whirlpool front-load models in this family (Duet, Duet Sport, WFW-series, and Whirlpool-built Kenmore front-loaders) is the drain pump assembly, Whirlpool part 280187 (also sold as WP280187; PartSelect number PS1485610). Parts retailers list this exact pump for the "won't drain / F21" fault across several hundred models in the family. Always confirm against your model number before ordering — later Whirlpool front-loaders use a different pump.

Affiliate slot — pending program approval

Whirlpool Drain Pump Assembly 280187 — buy links for PartSelect and RepairClinic will appear here once our affiliate accounts are active. Until then, search part number 280187 at your preferred parts retailer and verify fit with your model number.

Difficulty and cost picture

Filter cleaning: easy, no tools, about 15 minutes. Pump replacement on this family: a moderate DIY job — the pump is reached from the front or bottom panel on most models, with two wire terminals and hose clamps. Professional repair for a failed pump typically runs in the $150–$450 range (parts and labor) per published 2026 repair-cost guides, which is why the free checks come first.

When to call a pro

Newer Whirlpool models show this same fault as F9 E1 — see our F9 E1 guide. If your code is about filling instead of draining, see F8 E1 (low water flow).

Sources

  • Whirlpool long-drain definition and ~8-minute window, F21/F02 equivalence — repair references citing Whirlpool's error code lists: Oh So Spotless, "Whirlpool Washer Error Codes"; Nick's Appliance Repair, "Whirlpool Washer Error Codes — Complete List & Fixes." Checked November 2026.
  • Causes and fix order (filter, hose, suds, pump) — ErrorCodePedia, "Whirlpool Washer Error F21: Causes, Fixes and Repair Cost (2026)"; HomeApplianceFixing, "Whirlpool Error Code F21" (pump resistance range). Checked November 2026.
  • Part 280187 verification and model fit — AppliancePartsPros catalog page for Whirlpool 280187 Drain Pump Assembly (AP3953640); PartSelect.ca, Drain Pump Kit 280187 (PS1485610) expert Q&A. Checked November 2026.

Some links on this page may become affiliate links; see our affiliate disclosure. FixCode HQ is not affiliated with Whirlpool.